67-72
PATCH
PANELS
Striving To Supply
The Best Quality 67-72 GMC/Chevrolet Truck Patch Panels
Available On The Market Today.
All Panels are 19 Gauge Steel or heavier. |
Descriptions
in Blue are
hyperlinks to pictures and or larger description.
Left = Drivers Side, Right = Passengers Side |
| Part
# |
Description |
Price |
Quantity |
| 67-72
Inner Cowl Repair Panel
New Item |
Each |
| 5724081 |
1967-72
Truck, Blazer, Jimmy, Suburban, & Panel Truck Inner Cowl
repair panel This
section covers the area under the windshield cowl cover which is
bolted on behind the hood, this panel runs across the entire top
of cab below windshield to firewall and extends down either side
of cab closing off the air box plenum sides, has all holes
pre-punched just like original for wiper transmission arms,
wiper hoses, heater blower motor, etc..... Click on light blue
main description for a picture of complete part. Click
on this link for close-up of heater fan mounting area.
This item ships UPS oversized III.
Minimum average shipping in the continental USA is $85.00 |
$245.00 |
|
| |
| 1969-72 Blazer
/ Jimmy Rocker Box Reinforcement Assembly Plate
New Item |
Each |
| 3529883 |
1969-72
Blazer / Jimmy rocker box reinforcement assembly plate. This
high quality replacement part is manufactured for GMCPauls Truck
Parts. This part reinforces the following 3 major points on the
underbody by bolting to and joining the rocker box & end cap
to the inside of bedside at the rear door pillar and attaches to
the step up in floor just behind front seat. They are a direct
bolt in replacement for the originals that commonly rust out in
these vehicles. Original 16ga steel construction made in the
USA. Specify left or right in cart.
Picture
of
Blazer / Jimmy rocker box reinforcement assembly plate installed
|
$129.00 |
|
| |
| 1969-72 Blazer
/ Jimmy Rear Cab Floor Support
New Item |
Each |
| 3529897 |
1969-72
Blazer / Jimmy rear cab floor support. This high quality
replacement part is manufactured for GMCPauls Truck Parts.
They are a direct replacement for the originals that commonly
rust out in these vehicles. Original 16ga steel construction
made in the USA. Specify left or right in cart.
Picture
of
Blazer / Jimmy rear cab floor support installed
|
$42.00 |
|
| |
| 69-72
Blazer / Jimmy B-Pillar Patch ( Rear Lower Door Pillar ) New Item |
Each |
|
7416891
|
1969-72
Chevy & GMC Blazer / Jimmy B-Pillar ( sits directly behind
the rear door
pillar inside the bedside ) for the front door, B-Pillar attaches to our
rocker box reinforcement plate with 3 body bolts and then
reinforces the back side of the bedside and the back of the
rear door pillar, and rear cab support so as to
prevent sagging and shifting of these highly important
structural components. 13
3/4"L X 4 3/4"W. This high quality
replacement part is manufactured for GMCPauls Truck Parts.
Original
16ga steel construction made in the
USA. Specify Left or Right in
cart. |
$140.00 |
|
| |
| 67-68
or 69-70 Complete Toe Panel Firewall W/O Factory A/C New Item |
Each |
|
7568890
|
67-68
or 69-70 Truck, Blazer, Jimmy, Suburban & Panel
truck complete toe panel and firewall for models without factory A/C.
Precision stamped with all the correct openings from original
gauge steel and coated in a EDP applied black primer for a
perfect replacement to your damaged or rusted original
firewall. Specify 67-68 or
69-70 model year in cart. Due to
differences in the mounting of the gas pedal the 69-70 style
is not correct for 71-72 vehicles. This items ships truck
freight and you will be contacted after purchase to approve
shipping costs. |
$160.00 |
|
| |
| 1967-72
Complete Cab Floor w/Braces
|
Each |
| 4022739 |
1967-72
Complete truck cab floor with all underneath support braces attached. An excellent reproduction of the entire low
hump cab
floor pan, 100% complete from side to side, including under the fuel tank.
Original gauge steel with a EDP applied black primer finish for
superior corrosion resistance. This high quality
replacement part is manufactured for GMCPauls Truck Parts. Ships truck freight $125 to a
Business or $165 to a Residence. |
$380.00 |
|
| |
| 1967-72 Truck Rear Cab Floor
Cross Member Assembly With L&R Rear Supports
New Item |
Each |
|
7428860
|
1967-72
truck rear cab floor cross member with left and right rear cab
supports attached at either end.
They are a direct replacement for the original that's commonly
rusted out in these trucks. This brace supports the rear of the
cab floor from underneath and extends from far left side rear of
cab to far right side under the floor and fuel tank, this part
has extensive structural importance and has the left and right
rear cab supports attached at either end, its is often rusty and
should be inspected while replacing the floor pan.
Original gauge steel with a EDP applied black primer finish for
superior corrosion resistance. This high quality
replacement part is manufactured for GMCPauls Truck Parts. This
item has separate shipping charges as it ships oversized II. |
$140.00 |
|
| |
| 67-72
Outer Cab Floor Extension |
Each |
| 3648249 |
This
section covers the outside 4" of the entire length of the
floor, it has the rocker channel, and rocker panel backing plate
with weep holes all built into the piece. Please choose
Left, Right, or Both. |
$59.95 |
|
| |
| 1967-72
Suburban 3rd Door Rocker Panel |
|
| 2266678 |
1967-72
Suburban rear passenger door rocker panel. 19 gauge steel EDP
coated in black primer. 100% exactly like originals. |
$49.95 |
|
| |
| 1969-72
Blazer/Jimmy Rocker Box |
Each |
| 1667939 |
1969-72
Blazer / Jimmy rocker box. Exact reproduction of the originals
with all bracing like originals. Available for either left or
right side. Comes with a EDP applied coating of black primer
over original heavy gauge steel for superior rust resistance.
This item ships Oversized II and has separate shipping charges. Specify
Left or Right in cart. |
$119.95 |
|
| |
| 1969-72
Blazer/Jimmy Rocker Box Cap |
Each |
| 1635625 |
1969-72
Blazer / Jimmy rocker box end caps. Available in left &
right sides. Comes with a EDP applied coating of black primer
over original heavy gauge steel for superior rust resistance.
100% exactly like original for a trouble free installation. Specify
Left or Right in cart. |
$54.95 |
|
| |
| 67-72
Outer Cab Roof |
Each |
| 6036682 |
1967-72
Outer cab roof panel. This section replaces the outer cab roof
skin from seam at back of cab forward to the windshield drip
rail and extends the full width of the
cab to the door
drip rails, This item ships
truck freight, minimum freight to a business is $105.00,
residential is $76.00 more, we will contact you if the freight
is any higher. |
$200.00 |
|
| |
| 1967-72
Cab Roof Drip Rail |
Each |
| 1640134 |
1967-72
Truck cab roof drip rail for left or right door opening. This is
the section of roof drip rail that begins at rear top of
windshield and goes over top edge then down back side of door
opening. Exactly like original. Specify Left or Right in cart. |
$28.95 |
|
| |
| 69-71
Inner Cab Roof Patch Panel |
Each |
| 728772 |
1969-71
Chevy or GMC truck inner cab roof patch panel, repair that rusted out area directly
behind the windshield with this 19 gauge steel panel. Will work
for 1967-68 & 1972 also but these cabs did not have mirror
mounting pads attached to inner roof. This item ships
Oversized II and has separate shipping charges. |
$90.00 |
|
| |
| Cab Corner
Left or Right Hand |
Each |
139696
L/R |
1967-72
Chevy & GMC truck, exterior cab corner. 19 gauge steel
construction just like original, coated with a EDP applied
black primer. Specify Left or Right in cart. |
$21.95
|
|
| |
| 67-72 Outer Rockers |
Each |
139695
L/R |
1967-72
Chevy & GMC truck, Suburban, Panel, Blazer, Jimmy outer
rocker panel, EXACTLY like original GM rocker panel, 19 gauge
steel construction with a EDP applied black primer coating.
These are NOT the inferior low quality 21 & 23 gauge steel
rockers sold by many for more, these are THE Very best rocker
made!! Specify Left or Right in cart. This
item ships Oversized I and has separate shipping charges. |
$22.00 |
|
| |
| 67-72 Outer Rocker Plug |
Each |
| 358709 |
67-72 Outer
Rocker plastic plug, goes in hole in front of rocker panel to
keep debris and moisture out. 2 required one per side. |
$.95 |
|
| |
| Inner Rocker
Backing Plate |
Each |
| 132275 |
Quality
At its Best Used Outside The Inner Rocker To Properly Join The
Outer Floor To The Outer Rocker Panel Which Closes Off the
Back Side Off the Outer Rocker. Not required if front &
rear outer floor patch panels are used. |
$12.95 |
|
| |
| Front Floor Patch Panel 27x27
DRS. or Pass. Side |
Each |
| 132278 |
1967-72
Chevy & GMC truck, Suburban, Blazer, Jimmy, Top Quality,
original heavy gauge steel construction, precision stamped for
a exact fit, This item ships Oversized II
and has separate shipping charges. |
$30.00 |
|
| |
| Rear
Outer Cab Floor |
Each |
| 132280 |
1967-72
Chevy & GMC truck, 28"
x 9"
Rear outer floor, original heavy gauge steel, can be modified by
cutting un-needed portion off for use on Blazer, Jimmy,
Suburban & Panel trucks. Specify left (drivers side) or
right (passenger side) in cart. |
$24.95 |
|
| |
| 67-72
Truck Deep Rear Cab Floor |
Each |
|
7383528
|
1967-72
Chevy & GMC truck, Deep rear cab floor, original heavy gauge
steel. This patch panels is shorter than but extends further
into the cab and wraps farther across backside of cab than our
above patch panel. Specify left (drivers side) or right
(passenger side) in cart. |
$60.00 |
|
| |
| Front
Fender Lower Rear Reinforcement Mounting Plate L&R |
Pair |
| 7913495 |
1967-72
Chevy & GMC truck, Suburban, Blazer, Jimmy, & Panel
truck front fender lower rear reinforcement mounting plate. Installs
directly behind the front door pillar and bolts to the front
edge of the front cab support and rear lower front fender
mounting bolt passes through this part to attach the fender.
Used to reinforce the front door pillar where fender attaches.
Sold as a pair includes both drivers & passenger sides.
Highest quality original gauge steel that's
EDP coated in black primer |
$21.00 |
|
| |
| Front Door
Pillar Left or Right |
Each |
| 132283 |
1967-72
Chevy & GMC truck, Suburban, Blazer, Jimmy, , Highest quality EDP coated
original gauge steel in black primer |
$18.95 |
|
| |
| Rear Door
Pillar |
Each |
| 132285 |
1967-72
Chevy & GMC truck, Blazer, Jimmy, Suburban or Panel truck rear door
pillar for Suburban front doors only, 12"High. Highest quality EDP coated
original gauge steel in black primer Specify Left or Right in
cart. |
$21.95 |
|
| |
| Kick (Cowl) Panel
Lower |
Each |
| 132288 |
1967-72
Chevy & GMC truck, Suburban, Panel, Blazer, Jimmy, 11"L
x 9"H lower footwell kick panel. Specify Left or Right in
shopping cart. |
$20.95 |
|
| |
| Front Cab
Support |
Each |
| 132292 |
1967-72
Chevy & GMC truck, Suburban, Panel, Blazer, Jimmy,
original heavy gauge steel, OEM Style Front Cab Support. Left
= Right specify quantity in cart. |
$15.95 |
|
| |
| Rear Cab
Support |
Each |
| 132295 |
Heavy Gauge OEM Style Left or Right Rear Cab Support.
Specify Left or Right In Cart. |
$19.95 |
|
| |
| Lower Rear
Front Fender Patch |
Each |
| 132303 |
1967-72
Chevy & GMC truck, Suburban, Panel, Blazer, Jimmy OEM 19 gauge
steel construction, available in left or right hand. 16"high
lower rear front fender patch. Specify left or right in
shopping cart. |
$19.95 |
|
| |
| Lower
Front Fender Cup Patch |
Each |
| 188363 |
1967-72
Chevy & GMC truck, Suburban, Panel, Blazer, Jimmy
Right lower front fender cup, 19 gauge steel, these come with
a EDP primered black coating applied. RIGHT SIDE ONLY
AVAILABLE |
$49.95 |
|
| |
| Inner Door
Bottoms |
Each |
| 132305 |
1967-72
Chevy & GMC truck, Suburban, Panel, Blazer, Jimmy inner
door bottom 100% exactly like original. 19 gauge steel just
like original not the thin 21 & 23 gauge steel available
from some sources, these come with a EDP primered black
coating applied. , Select Left or Right in shopping cart. This
item ships Oversized I and has separate shipping charges. |
$32.95 |
|
| |
| 13
3/4 High Outer Door Skin |
Each |
| 132306 |
1967-72
Chevy & GMC truck, Suburban, Panel, Blazer, Jimmy, lower
outer door skin 19 gauge steel, these come with a EDP primered
black coating applied. 13 3/4" High. Specify Left
or Right in cart. This item ships
Oversized I and has separate shipping charges. |
$21.95 |
|
| |
| FULL
Outer
Door Skin |
Each |
| 132310 |
1967-72
Chevy & GMC truck, Suburban, Panel, Blazer, Jimmy full
outer door skin. 100% exactly like original. 19 gauge steel
just like original not the thin 21 & 23 gauge steel
available from some sources, these come with a EDP primered
black coating applied. This item ships
Oversized II
and has separate shipping charges. |
$79.95 |
|
| |
|
|